Whirlpool Washer Sud Code (Quick Fix Guide)
Seeing the “Sud” or “Sd” error code on your Whirlpool washer can be annoying. But don’t worry, we’ve got you covered.
The Sud error means your washer has too much suds during the wash cycle.
This can really slow down your washer’s performance. When you see the Sud code, your washer will take longer to rinse out the suds. This is its way of trying to fix the problem.
Table of Contents
What Triggers the Sud Error Message
The Sud error on your Whirlpool washer can be caused by a few things:
- Using too much laundry detergent – Even HE detergents can cause too many suds if used too much.
- Using the wrong type of detergent – Non-HE detergents can cause problems in front-loading washers.
- Overuse of fabric softener – Too much fabric softener can also cause suds buildup.
How the Sud Detection System Works
Whirlpool’s sud detection system checks the water level and resistance during spin. If it finds too many suds, it shows the Sud error code. This helps avoid oversudsing, which can cause poor rinsing and damage to the washer.
Common Sud Code Display Patterns
When the Sud error is shown, you’ll see one of two patterns on your Whirlpool washer:
- The “Sud” or “Sd” error code on the screen.
- The “Sud” or “Sd” code with the Rinse status light on, showing the load may not be rinsed well.
If the Complete Cycle light is on with the Sud code, it means water might not be fully removed. This can make drying times longer.
High-Efficiency Detergent Requirements for Whirlpool Washers
The type of detergent you use in your Whirlpool washer is crucial. It can prevent a frustrating “sud” error message. Whirlpool washers work best with High-Efficiency (HE) detergents. These detergents create fewer suds and rinse out more completely in low-water washing conditions.
Using a non-HE detergent or adding too much can cause too many suds. This leads to the sud error code. Always measure your detergent carefully, following the manufacturer’s instructions. This depends on your load size and soil level. For Whirlpool washers with bulk dispensers, make sure the dispenser is enabled and the concentration level is set right to avoid over-dispensing.
| Detergent Type | Recommended Use | Impact on Suds |
|---|---|---|
| High-Efficiency (HE) Detergent | Specially formulated for low-water washing | Produces fewer suds |
| Non-HE Detergent | Not recommended for Whirlpool washers | Can cause excessive suds |
Using the right HE detergent and following the manufacturer’s guidelines can prevent the sud error code. This keeps your Whirlpool washer running smoothly and your clothes looking great.
Immediate Solutions for Whirlpool Washer Sud Code
If your Whirlpool washer shows a “Sud” or “Sd” error, don’t worry. This usually means there’s too much suds. This can make your wash cycles less efficient and longer. Luckily, there are quick fixes you can try.
Emergency Reset Procedures
At times, a simple reset can clear the Sud code. Here’s what to do:
- Unplug the washer for 1 minute.
- Plug it back in and start the cycle again.
- If the Sud code doesn’t go away, move on to the next steps.
Rinse Cycle Solutions
The Sud code might mean there’s too much suds. Let the cycle finish as it tries to get rid of the suds. If it still shows the code, try a Rinse/Spin cycle to wash out more suds.
Manual Suds Reduction Methods
For tough Sud codes, you can manually cut down suds. Run an empty cycle with regular liquid bleach, or use affresh® to clear out suds-causing agents.
If you’ve used “no splash” or “easy pour” bleach, it might be causing the suds. An empty cycle with regular liquid bleach can help get rid of these suds.
By trying these quick fixes, you can often fix the Whirlpool washer Sud code. Remember, using the right amount of HE detergent helps avoid Sud codes in the future.
Preventing Future Sud Error Messages
To keep your Whirlpool washer working well, it’s important to use the right detergent. Always choose high-efficiency (HE) detergent. Also, measure it right for your load size and how dirty it is. Swash® HE Ultra-Concentrated Liquid Laundry Detergent is a good choice because it dispenses just the right amount.
If you keep getting Sud errors, try a “Clean Washer” cycle. It removes old detergent that might cause problems. Don’t use “no splash” or “easy-pour” bleach because it can make too many suds. Also, using affresh® washer cleaner often helps keep your washer in top shape and stops detergent buildup.
- Use high-efficiency (HE) detergent and measure carefully according to load size and soil level
- Consider Swash® HE Ultra-Concentrated Liquid Laundry Detergent for precise dispensing
- Run a “Clean Washer” cycle to remove residual detergent buildup
- Avoid using “no splash” or “easy-pour” liquid chlorine bleach
- Regularly clean your washer with affresh® washer cleaner
By following these tips, you can make sure your Whirlpool washer runs smoothly. This will prevent future Sud light blinking and other problems.
Advanced Troubleshooting for Persistent Sud Issues
If you’re still facing suds problems with your Whirlpool washer, it’s time to look closer. First, make sure your bulk dispenser is turned on and set right. Wrong settings can cause too much suds.
Even with the right detergent, suds might still be a problem. Try running several “Clean Washer” cycles to clean out the machine. Sometimes, unplugging the washer for a few minutes can reset it and fix issues.
If whirlpool washer error codes about suds keep showing up, it might mean a bigger issue. This could be with the washer’s sensors or control system. At this point, it’s wise to call a professional. They can find and fix any whirlpool front load washer problems causing the suds.
Related Articles:
