Your Blomberg washing machine has probably done it again.
You start your laundry and everything goes on smoothly.
Now it’s time to drain your washer and it’s not draining.
It’s probably draining but at a snail’s pace.
This can always get frustrating.
But don’t worry, today, we are going to help you fix this problem of Blomberg washing machine not draining.
There are a few possible reasons why your Blomberg washer is not draining.
In this article, we are going to explain the 9 common reasons why your Blomberg washing machine is not draining.
Here are the reasons why your Blomberg washer may not be spinning:
- The Drain hose is clogged
- The filter is clogged
- The pump may be damaged
- A clogged drain
- Blockage in drain pump
- Your washer is overloaded
- Your washing machine is unleveled
- A problem with the drive belt
- The lid switch may be faulty
A Blomberg washing machine drainage error is indicated by a 02 code.
Table of Contents
Why is my Blomberg washing machine not draining? (troubleshooting tips)
There are many reasons why your Blomberg washer won’t drain. Luckily, they aren’t overly complex and you will be able to solve the issues without having to pay for the service of an electrician.
Below are some of the most common causes of a Blomberg washing machine not draining.
You will have your washer draining again by following through with these easy troubleshooting tips.
1. The drain hose is clogged
The first thing you’ll want to check if your Blomberg washing machine isn’t draining is the drain hose.
This is the hose that carries water from the washing machine to the drain.
If this hose is clogged, trapped, or kinked, it could be preventing water from draining properly.
- Start by unplugging your washing machine and
- Disconnect the drain hose from the back of the machine.
- Next, use a plunger to try and clear any blockages in the hose.
- If that doesn’t work, you can try using a plumber’s snake or a stiff wire to clear the clog.
- Once you’ve cleared the clog, reattach the drain hose and plug your washing machine back in.
- Run a test cycle to see if the problem is fixed.
2. The washing machine filter is clogged
Another possible reason for a Blomberg washing machine not draining properly is a clogged filter.
Most washing machines have a lint filter that collects lint and other debris during the washing cycle.
If this filter becomes clogged, it can prevent water from draining properly.
- Start by unplugging the machine and locating the filter.
It’s usually located behind a panel near the bottom of the machine.
- Once you’ve found it, remove the filter and clean it with warm, soapy water.
If the filter is severely clogged, you may need to replace it.
Consult your washing machine’s manual for instructions on how to do this or get your appliance technician to assist you.
3. The pump is damaged
A common reason why your Blomberg washing machine isn’t draining properly is that the pump is damaged.
The pump is responsible for moving water from the washing machine to the drain, so if it’s not working properly, it can prevent the water from draining.
If you suspect that the pump is damaged, you’ll need to replace it. Consult your washing machine’s manual for instructions on how to do this or contact an expert to get it done for you.
4. The drain is clogged
If your Blomberg washing machine isn’t draining, it could be because the drain itself is clogged.
When water can’t drain properly from the washing machine, it can cause a backup and prevent the machine from draining properly.
Check the drain into which your Blomberg washing drains and ensure that it is free from any clogs or blockages that may be causing water to back up in the drain hose and causing your washer not to drain.
5. There’s something blocking the drain pump
Your Blomberg washing machine may not be draining properly because there’s something blocking the drain pump.
The drain pump is responsible for moving water from the washing machine to the drain, so if it’s blocked, it can prevent the water from draining.
- Start by unplugging your washing machine
- Locating the pump, which is usually behind a panel near the bottom of the machine on top load Blomberg washing machines.
On front load washers, it is usually located in the front below the door.
- Once you’ve found it, remove any debris or blockages that you see.
- This is how to unblock your Blomberg washing machine pump.
If the pump is damaged, you’ll need to replace it.
You can refer to your washing machine’s manual for instructions on how to replace the pump motor for your model.
6. Your washing machine is overloaded
Yes, your Blomberg washing machine may not be draining properly because you have overloaded it.
If you try to wash too many clothes at once, it can prevent the water from draining properly.
To fix this problem, simply reduce the number of clothes that you’re washing at one time.
You should also make sure that you’re not overloading the washing machine by checking the manufacturer’s instructions.
7. Your washing machine is unlevel
If your Blomberg washing machine isn’t draining properly, it could be because it’s not level.
If the washing machine is not level, it can prevent the water from draining properly.
To fix this problem, simply adjust the legs of the washing machine until it’s level.
You can use a spirit level to check if the machine is level.
8. There is a problem with the Drive Belt
The drive belt on your washing machine is what makes the pump work.
If you notice any signs that the drive belt has started stretching or breaking, that could be a reason why your Blomberg washer isn’t draining.
You will need to turn your washer on its back to properly assess the state of the drive belt.
If you are not technically inclined you might want to invite your appliance technician to do a proper assessment of your washer.
9. The Lid switch may be faulty
The Lid switch serves to sense when the door is shut so that your washing machine can operate.
If this small plastic switch is broken, it may cause drainage issues with any clothes in need of a spin cycle!
With an open door and your cycle running, press the switch by hand.
If it produces a clicking sound that means it is functioning.
Otherwise, the switch is broken and you may need to get it replaced preferably by an expert.
How do you manually drain a Blomberg washing machine?
There are times when the only option you will have is to manually drain your Blomberg washing machine.
We are going to teach you how you can manually drain your Blomberg washer If all else fails.
This is a simple step-by-step process you can follow in other not to make any mess.
Supplies you need to drain your Blomberg washer manually:
- A bucket
- Plumbers snake
- Needle-nose pliers
- A Shallow container
How to manually drain a Blomberg Top load washing machine
If you have tried all the troubleshooting tips above and still your washer doesn’t drain, it’s time to do a manual drain!
Follow these steps below to manually drain your Blomberg washing machine safely.
1. Turn off the power to your washer
It is always safe to make sure that you turn off the power supply to your washer before starting a manual draining process.
For extra safety, you can switch off the circuit breaker as well.
2. Locate the drain hose
The drain hose on a top-load Blomberg washing machine is located at the back.
Position your washer such that you have enough space to work at the back.
Lay towels onto the floor to soak up any water that spill.
Turn off the water supply(hot, cold, and grey) to your washer by disconnecting the drain hose from the pipe.
Hold the drain hose above the washer so that water doesn’t spill unexpectedly.
3. Drain the water into a bucket
Drain the water from your tub by lowering the drain hose into a bucket and letting the water flow into it.
Secure the drain hose in a good position( insert back into the pipe) and empty the bucket when it gets full.
Repeat these steps till you have completely drained all the water in your tub.
How to manually drain a Blomberg front load washing machine
1. Turn off the power to your washer
It is always safe to make sure that you turn off the power supply to your washer before starting a manual draining process. For extra safety, you can switch off the circuit breaker as well.
2. Locate the drain hose
Your front load Blomberg washer will either have a single drain pump filter or a drainpipe filter and a separate drain hose.
Whichever one you have, you can usually access it behind the front button panel on your washer.
Removing the panel depends on your Blomberg washing machine.
Refer to your user manual for instructions on how to remove the panel to locate the drain hose.
3. Drain the water
If your washer has a drain pump filter only, position the shallow container up directly under the pump filter to collect the water.
Turn the knob gently to allow water to flow out.
Once the container gets full, turn the knob in the opposite direction to close it, and empty the container.
Repeat the process till all the water has drained.
If your washer has a drain pump and a tube, unclip the tube and unscrew the end cap when you are ready to collect the water.
After draining all the water, fix back the cap and clip back the drain hose in place.
4. Clean the filter
Using warm water and a brush, scrub the filter to make sure that it is free from any debris or foreign materials.
There you go.
If your Blomberg washing machine does not drain at any point during your laundry, be sure to try the troubleshooting tips we have given in this article.