9 Reasons Beko Dryer Keeps Stopping (How To Fix it Quickly)
Beko dryer stopping abruptly is a common problem that many users encounter during a cycle. This can be frustrating, especially when you’re in a hurry and need your clothes dried quickly.
Here are 9 possible reasons why your Beko dryer keeps stopping:
- Overheating
- Faulty Thermostat
- Clogged Vent
- Worn Out Drum Glides
- Defective Motor
- Broken Belt
- Faulty Start Switch
- Damaged Door Latch
- Control Board Issues
In this article, we have outlined quick solutions to fix your stopping Beko dryer.
Table of Contents
Why Beko dryer keep stopping (Quick Solutions)
If your Beko dryer keeps stopping when it is not supposed to, there is likely a problem that needs to be fixed. Here are the common reasons why this may be happening, and how you can fix it by yourself.
1. Overheating
When the dryer overheats, it can cause components to wear out more quickly. In extreme cases, it can even lead to a fire hazard. Overheating typically occurs when the dryer’s ventilation is blocked, causing hot air to become trapped in the dryer. This can cause the dryer’s safety thermostat to trip and the machine to stop as a protective measure.
How to Fix dryer overheating:
- Make sure the dryer vent is not blocked or kinked. Clean it out if necessary.
- A clogged lint filter can restrict airflow and cause overheating. Clean the lint filter after every load.
2. Faulty Thermostat
The thermostat regulates the temperature inside the dryer drum. When the dryer’s temperature rises too high, the thermostat cuts off the power to the heating element. A faulty thermostat can cause your dryer to go off abruptly.
How to fix dryer thermostat:
- Test the thermostat: You can test the thermostat using a multimeter. If it doesn’t have continuity at room temperature, it needs to be replaced.
If you suspect your dryer vent is clogged, here’s how you can unclog it:
3. Clogged Vent
The vent allows hot, moist air to escape from the dryer during a cycle. If the vent is clogged, this air can’t escape, which can cause the dryer to overheat and stop.
How to unclog dryer vent:
- Unplug the dryer and disconnect the vent hose from the back of the dryer and the wall.
- Use a vent cleaning brush to remove lint and debris from the vent hose and the vent opening in the wall. You can also use a vacuum cleaner to suck out the lint.
- Once the vent is clean, reconnect the vent hose to the dryer and the wall, ensuring it’s not kinked or crushed.
- Run a drying cycle to see if the problem is resolved.
4. Worn Out Drum Glides
Drum glides, also known as drum bearings, are plastic or nylon pieces that support the front of the dryer drum. As the drum rotates, it slides along these glides. If the drum glides wear out, the drum can start to wobble, causing the dryer to vibrate and potentially stop.
How to Replace Worn Out Drum Glides:
If you suspect that the drum glides are the issue, here’s how you can replace them:
- Unplug the dryer before starting any repair work.
- Remove the top and front panels of the dryer to access the drum glides.
- The drum glides are typically located at the front edge of the drum. Remove the old glides by unscrewing or unclipping them.
- Attach the new drum glides in the same location as the old ones. Make sure they’re securely fastened.
- Once the new drum glides are installed, reassemble the dryer by replacing the front and top panels.
- Run a drying cycle to see if the problem is resolved.
5. Defective Motor
If the motor is defective, it may not provide enough power, causing the dryer to stop.
How to Address a Defective Motor:
If you suspect that the motor is the issue, here’s how you can address it:
- Unplug the dryer and open the back panel to access the motor. Look for any visible signs of damage or wear.
- Test the motor using a multimeter. If it doesn’t show continuity, it needs to be replaced.
- If the motor is defective, it will need to be replaced. Make sure to purchase a replacement part that is compatible with your Beko dryer model.
6. Broken Belt
Over time, the belt can wear out or break, causing the dryer to stop. When this happens, the dryer’s drum doesn’t tumble but you can hear the motor running.
Steps to Replace the Belt:
If you suspect that the belt is the issue, here’s how you can replace it:
- Unplug the dryer
- Remove the front panel of the dryer to access the belt.
- Take note of the belt’s path, then remove the old belt from the motor and drum.
- Place the new belt around the drum and motor pulley following the same path as the old belt.
- Once the new belt is installed, reassemble the dryer by replacing the front panel.
- Run a drying cycle to see if the problem is resolved.
7. Faulty Start Switch
The start switch in your Beko dryer is what initiates the drying cycle when you press the start button. If the start switch is faulty, it may not send these signals correctly, causing the dryer to stop or not start at all.
How to Fix a Faulty Start Switch:
If you suspect that the start switch is the issue, here’s how you can fix it:
- Test the start switch using a multimeter. If it doesn’t show continuity when activated, it needs to be replaced.
- If the start switch is faulty, it will need to be replaced. Make sure to purchase a replacement part that is compatible with your Beko dryer model.
8. Damaged Door Latch
The door latch on your Beko dryer ensures that the dryer door stays securely closed during a cycle. If the door latch is damaged or broken, the door may not stay closed, causing the dryer to stop mid-cycle.
How to Replace a Damaged Door Latch:
If you suspect that the door latch is the issue, here’s how you can replace it:
- Unplug the dryer.
- Use a screwdriver to remove the screws holding the door latch in place, then pull out the old latch.
- Insert the new latch into the slot and secure it with the screws.
- Close the door and start a drying cycle to see if the problem is resolved.
9. Control Board Issues
The control board manages all of the dryer’s functions, from regulating the temperature to controlling the motor. If the control board has issues, it may not send the correct signals to the other components, causing the dryer to stop.
How to Address Control Board Issues:
If you suspect that the control board is the issue, here’s how you can address it:
- Reset the control board: Sometimes, a simple reset can solve the problem. Unplug the dryer for a few minutes, then plug it back in to see if the problem is resolved.
- Check for visible damage: Unplug the dryer and open the back panel to access the control board. Look for any visible signs of damage, such as burns or bulging capacitors.
- Replace the control board: If the control board is faulty, it will need to be replaced. Make sure to purchase a replacement part that is compatible with your Beko dryer model.
Conclusion
While many of these issues can be addressed with a bit of troubleshooting and some basic tools, always prioritize safety. If you’re not comfortable doing these repairs yourself or if the problem persists, don’t hesitate to call in a professional.
Related articles:
