Roper Washing Machine Won’t Drain (All you need to know)
How frustrating and time-wasting it can be when you have finished a wash cycle and refuses to drain or is taking forever.
The water just sits in your drum looking you in the face.
No, your washer is not necessarily broken. So calm down and read on.
If your Roper washing machine isn’t draining, there are a few possible reasons.
We’ll go over 10 of the most common reasons why your washing machine might not be draining properly, as well as what you can do to fix the problem.
Here are the reasons why your Roper washer may not be spinning:
- The Drain hose is clogged
- The filter is clogged
- The pump may be damaged
- A clogged drain
- Blockage in drain pump
- Your washer is overloaded
- Too much detergent
- Your washing machine is unleveled
- A problem with the drive belt
- The lid switch may be faulty
Table of Contents
Why won’t my Roper washing machine drain? (With troubleshooting tips)
Below are some of the most common causes of a Roper washing machine not draining.
You will have your washer draining again by following through with these easy troubleshooting tips.
1. The drain hose is clogged
The first thing you’ll want to check if your Roper washing machine isn’t draining is the drain hose.
This is the hose that carries water from the washing machine to the drain.
If this hose is clogged, trapped, or kinked, it could be preventing water from draining properly.
Troubleshooting Tips
- Start by unplugging your washing machine and
- Disconnect the drain hose from the back of the machine.
- Next, use a plunger to try and clear any blockages in the hose.
- If that doesn’t work, you can try using a plumber’s snake or a stiff wire to clear the clog.
- Once you’ve cleared the clog, reattach the drain hose and plug your washing machine back in.
- Run a test cycle to see if the problem is fixed.
2. The washing machine filter is clogged
Another possible reason for a Roper washing machine not draining properly is a clogged filter.
Most washing machines have a lint filter that collects lint and other debris during the washing cycle.
If this filter becomes clogged, it can prevent water from draining properly.
Troubleshooting Tips
- Start by unplugging the machine and locating the filter.
It’s usually located behind a panel near the bottom of the machine. - Once you’ve found it, remove the filter and clean it with warm, soapy water.
If the filter is severely clogged, you may need to replace it.
Consult your washing machine’s manual for instructions on how to do this or get your appliance technician to assist you.
3. The pump is damaged
A common reason why your Roper washing machine isn’t draining properly is that the pump is damaged.
The pump is responsible for moving water from the washing machine to the drain, so if it’s not working properly, it can prevent the water from draining.
Troubleshooting Tips
If you suspect that the pump is damaged, you’ll need to replace it. Consult your washing machine’s manual for instructions on how to do this or contact an expert to get it done for you.
4. The drain is clogged
If your Roper washing machine isn’t draining, it could be because the drain itself is clogged.
When water can’t drain properly from the washing machine, it can cause a backup and prevent the machine from draining properly.
Troubleshooting Tips
Check the drain into which your Roper washing drains and ensure that it is free from any clogs or blockages that may be causing water to back up in the drain hose and causing your washer not to drain.
Read Also: How to Clean Roper Washing Machine (Step by step)
5. There’s something blocking the drain pump
Your Roper washing machine may not be draining properly because there’s something blocking the drain pump.
The drain pump is responsible for moving water from the washing machine to the drain, so if it’s blocked, it can prevent the water from draining.
Troubleshooting Tips
- Start by unplugging your washing machine
- Locate the pump, which is usually behind a panel near the bottom of the machine on top-load Roper washing machines.
- Once you’ve found it, remove any debris or blockages that you see.
- This is how to unblock your Roper washing machine pump.
If the pump is damaged, you’ll need to replace it.
You can refer to your washing machine’s manual for instructions on how to replace the pump motor for your model.
6. Your washing machine is overloaded
Yes, your Roper washing machine may not be draining properly because you have overloaded it.
If you try to wash too many clothes at once, it can prevent the water from draining properly.
Troubleshooting Tips
To fix this problem, simply reduce the number of clothes that you’re washing at one time.
You should also make sure that you’re not overloading the washing machine by checking the manufacturer’s instructions.
7. Your washing machine is unlevel
If your Roper washing machine isn’t draining properly, it could be because it’s not level.
If the washing machine is not level, it can prevent the water from draining properly.
Troubleshooting Tips
To fix this problem, simply adjust the legs of the washing machine until it’s level.
You can use a spirit level to check if the machine is level.
8. There is a problem with the Drive Belt
The drive belt on your washing machine is what makes the pump work.
If you notice any signs that the drive belt has started stretching or breaking, that could be a reason why your Roper washer isn’t draining.
Troubleshooting Tips
You will need to turn your washer on its back to properly assess the state of the drive belt.
If you are not technically inclined you might want to invite your appliance technician to do a proper assessment of your washer.
9. The Lid switch may be faulty
The Lid switch serves to sense when the door is shut so that your washing machine can operate.
If this small plastic sitch is broken, it may cause drainage issues with any clothes in need of a spin cycle!
Troubleshooting tips
With an open door and your cycle running,–press the switch by hand.
If it produces a clicking sound that means it is functioning.
Otherwise, the switch is broken and you may need to get it replaced preferably by an expert.
10. Too much detergent
When you use too much detergent in your laundry It tends to cause a lot of suds which will cause your rover washer to not drain properly or even not drain at all.
Troubleshooting tips
Ensure that you measure and follow the detergent instructions for your load.
If you realize that there are too many suds in your washer, you can reduce or clear it by selecting Rinse & Spin. Don’t add additional detergent to the load.
Read also: Can a Washing Machine Drain into a Floor Drain? (Answered)
How do you manually drain a Roper washing machine?
Sometimes the only option you will have is to manually drain your Roper washing machine.
We are going to teach you how you can manually drain your Roper washer If all else fails.
This is a simple step-by-step process you can follow in other not to make any mess.
Supplies you need to drain your Roper washer manually:
- A bucket
- Screwdriver
- Plumbers snake
- Towel
- Needle-nose pliers
- A Shallow container
How to manually drain a Roper Top load washing machine
If you have tried all the troubleshooting tips above and still your washer doesn’t drain, it’s time to do a manual drain!
Follow these steps below to manually drain your Roper washing machine safely.
1. Turn off the power to your washer
It is always safe to make sure that you turn off the power supply to your washer before starting a manual draining process.
For extra safety, you can switch off the circuit breaker as well.
2. Locate the drain hose
The drain hose on a top-load Roper washing machine is located at the back.
Position your washer such that you have enough space to work at the back.
Lay towels onto the floor to soak up any water that spill.
Turn off the water supply(hot, cold, and grey) to your washer by disconnecting the drain hose from the pipe.
Hold the drain hose above the washer so that water doesn’t spill unexpectedly.
3. Drain the water into a bucket
Drain the water from your tub by lowering the drain hose into a bucket and letting the water flow into it.
Secure the drain hose in a good position( insert back into the pipe) and empty the bucket when it gets full.
Repeat these steps till you have completely drained all the water in your tub.
Conclusion
That is it.
We have covered all the common possible reasons why your Roper washing machine won’t drain and easy ways to troubleshoot the problems.
So no need to worry again.
With these, you will be able to fix your Roper washing machine not draining problems without any hustle.
Reference:
Roper washing machine user and care guide
